Toggle sidebar Toggle sidebar

Search results

  1. Keith Rittenberry

    ISO 0.866 Piston Pins

    Got some right away from SD. Thanks everyone for responding.
  2. Keith Rittenberry

    ISO 0.866 Piston Pins

    Looking for some good used or new 0.866 piston pins. Length from 2.250-2.500. Call Keith at 952-250-314five.
  3. Keith Rittenberry

    Small Block Chevy - Bracket Motor

    Price?
  4. Keith Rittenberry

    Lithium Battery Dealer

    EarthX, Kadex, and Concorde have pma's lithium batteries
  5. Keith Rittenberry

    SOLD!!!! New Diamond Pistons for Wedge SBC SOLD!!!!

    Mike, would you sell the crank separately? Call if you would. Keith at 952-250-3145.
  6. Keith Rittenberry

    ISO 6.00 Gear set

    I have a gear set. 9 inch. Has three runs on it. Want photos? Keith Rittenberry 952-250-3145
  7. Keith Rittenberry

    GARAGE SALE

    Bob, specs on the cam? Lift, duration at .050, lobe separation, etc.
  8. Keith Rittenberry

    1150 Carb

    Already bought one. Thanks.
  9. Keith Rittenberry

    1150 Carb

    Anyone have a good 1150 Dominator style carb for sale?
  10. Keith Rittenberry

    WTB Aluminum BBC Block

    Looking for a good BBC aluminum block, standard bore spacing.
  11. Keith Rittenberry

    Rocket block

    Rumor has it (and I also read it somewhere) that Dart built the rocket block for GM. The rocket block and iron eagle are identical in specs as far as I can tell. Being they are both 4.4" bore spacing blocks, with Dart saying 4.185" is the largest recommended bore for the iron eagle, I'd say...
  12. Keith Rittenberry

    Hancock and Lane Racing parts sale

    My mistake (again). I meant to say 55mm cams, non-SB2.
  13. Keith Rittenberry

    Hancock and Lane Racing parts sale

    952-250-3145, [email protected]
  14. Keith Rittenberry

    Hancock and Lane Racing parts sale

    Jeff, I'm interested in your selection of 50mm cams for a SBC, but not for a SB2. Do you have any that are not SB2? If so, how can I get a peek at the specs? I'm looking for something in the 278-282 intake duration @ .050, 114 lobe separation, .485 -.490 lobe lift.
  15. Keith Rittenberry

    Interesting Tid Bit

    No win situation for Tim, I'd say.
  16. Keith Rittenberry

    can someone please help me ?

    Attached is the manual you need. And just in case the manual doesn't load as planned, here is the link to it: https://www.autometer.com/media/2650-823X.pdf Good luck!
  17. Keith Rittenberry

    Wanted sheet metal intake

    Too bad you don't need an 18* intake for 9.0 deck. I have a Hogan loaded with new carbs, linkage, new regulator, new hoses and fittings, etc. You can have it with two new 750 Dominators or with two older BREs @ 1100 CFM. Or, you can have all four carbs with the package.
  18. Keith Rittenberry

    Parts for sale

    My mistake, Todd. The intake rockers I need are marked CZKR70 and CZKL70, and exhaust rockers marked CCAR 1.60 and CCAL 1.60. Thanks, Keith
  19. Keith Rittenberry

    Parts for sale

    Todd, Do you have any .180 offset intake in 1.7 ratio? Any 1.6 ratio exhaust? Any pairs on the shaft? Thanks, Keith
  20. Keith Rittenberry

    8 3/4 pro gear

    Heat the gears to take out the heat treatment, huh? Some say cryo them to make them stronger. I'd ask one of the gear manufacturers for the Rockwell hardness of a pro gear, then have a reputable machinist check the hardness of your "re-heated" standard gears to see if you get close to that...
Top Bottom
Back